Wooden Door Installation & Repair Services in Singapore
Are you searching For Door Repair Services in Singapore? The R N Engineering and Construction PTE Ltd. is a Professional Door Repair Services provider for all kind of service and repair. We are available in 24 Hours. Call Us +65-87335544.
Commercial Wood Door Repairs, Wood Doors Replacement, Emergency Commercial Door Repair Services in Singapore.
Are you looking for Door Repair Services in Singapore? We are available here. Our experienced carpentry team can hang, install, and repair all styles of internal and external doors for your home or business. Our mission is to provide you with the best quality services in Singapore.
R N Engineering and Construction PTE Ltd. is the tremendous services provider for its best-rated carpentry team in Singapore. We offer domestic & commercial services in Singapore. Contact Us +65-87335544
Our Service List:
- Door frame repair
- Rotted door frame repair
- Damaged door frame repair
- split door frame repair
- Broken door frame repair
- Bedroom door frame repair
- exterior door frame repair and replacement
- front door frame repair
- door jamb repair
- steel door frame repair
- Cabinet door hinge repair
- Broken door hinge repair
- Adjusting door hinge repair and replacement
- Repair cabinet door hinge hole
- Commercial door pivot hinge repair
- Garage door hinge repair
- Garage door hinge replacement
- Loose door hinge repair
- Wooden cabinet hinge repair
- Broken garage door hinge and roller replacement
Wooden Door Installation Process:
Installing a wood door is a project that requires careful planning and attention to detail. Below is a general overview of the wood door installation process. Keep in mind that specific instructions may vary depending on the type of door and frame you’re working with.
Materials and Tools You Will Need:
- Wood door
- Door frame or door jamb (if replacing an existing door)
- Shims
- Screws
- Screwdriver or drill
- Hinges
- Lockset
- Tape measure
- Level
- Carpenter’s square
- Pry bar
- Pencil
- Safety glasses and work gloves


Installation Steps:
- Prepare the Opening:
- If you’re replacing an existing door, remove the old door, trim, and hardware.
- Ensure that the rough opening is plumb, level, and square. Use a level and carpenter’s square to check.
- Measure the Door:
- Measure the height and width of the door to ensure it will fit the opening properly.
- Prepare the Door:
- If the door is not pre-hung (attached to the frame), attach the hinges to the door according to the manufacturer’s instructions.
- Install the Frame (If Necessary):
- If you have a pre-hung door, you’ll need to install the frame first. Make sure it is plumb, level, and square in the opening. Shim as necessary to achieve proper alignment.
- Hang the Door:
- With the help of a friend, lift the door into the opening.
- Attach the hinges to the door frame or jamb using screws. Make sure they are aligned correctly.
- Check for Proper Fit:
- Close the door and check for even gaps around all sides. Adjust the shims as necessary to ensure the door is level and plumb.
- Secure the Door:
- Once the door fits properly and is level, secure it in place with screws. Drive screws through the hinges and shims into the frame.
- Install the Lockset:
- Follow the manufacturer’s instructions to install the lockset, deadbolt, and strike plate. Mark and drill holes for the doorknob and latch, then attach the hardware.
- Test the Door:
- Ensure the door opens and closes smoothly, latches properly, and locks securely.
- Add Trim and Finish:
- Install door casing and trim around the door to cover any gaps between the door frame and the wall. Fill any gaps or holes with wood putty, and finish the door with paint or stain as desired.
- Clean Up:
- Remove any excess shims, debris, and tools from the work area.
This is a basic guide to installing a wood door. Keep in mind that different doors and frames may have specific installation instructions, so always refer to the manufacturer’s guidelines.
Wooden Door Repair Process:
Repairing a wood door can involve fixing various issues such as scratches, dents, cracks, loose hinges, or alignment problems. The specific repair process will depend on the type and extent of the damage. Here is a general overview of the wood door repair process:
Materials and Tools You Will Need:
- Wood filler
- Sandpaper (various grits)
- Putty knife
- Paint or wood stain (matching the door)
- Paintbrush or foam brush
- Paintbrush or foam brush
- Screwdriver
- Wood glue
- Clamps
- Hammer
- Replacement hardware (if needed
Repair Steps:
- Assess the Damage:
- Examine the door to determine the extent of the damage. Identify any scratches, dents, cracks, or loose hardware.
- Remove the Door (if necessary):
- If the damage is extensive or if you need to repair the door in a more convenient location, remove the door from its hinges. This is typically done by unscrewing the hinges from the door frame.
- Fix Scratches and Dents:
- For minor scratches and dents, use wood filler. Apply a small amount of wood filler to the damaged area, smooth it with a putty knife, and let it dry. Sand the repaired area until it’s smooth and flush with the rest of the door. Repeat if necessary.
- Repair Cracks:
- If you have cracks in the door, apply wood glue into the crack, align the pieces, and use clamps to hold them together until the glue dries. Sand any excess glue and finish the surface as needed.
- Sand the Door:
- Sand the entire door with a medium-grit sandpaper to prepare the surface for paint or stain. Start with coarse sandpaper and work your way to finer grits for a smooth finish.
- Repaint or Restain:
- Apply a paint or wood stain that matches the door’s existing finish. Follow the manufacturer’s instructions for the paint or stain you are using. Apply multiple coats if necessary, allowing each coat to dry before adding the next.
- Reattach Hardware:
- If you removed the door, reattach it to the hinges. Check that the door swings smoothly, and adjust the hinges if needed.
- Tighten Loose Hardware:
- If any hardware is loose, such as screws in hinges or handles, tighten them with a screwdriver or replace them if they are damaged.
- Test the Door:
- Open and close the door to ensure it operates correctly. Check for proper alignment and latch function.
- Final Touch-Ups:
- If you repaired any scratches, dents, or cracks, touch up the paint or stain as needed to blend the repaired areas with the rest of the door.
Remember that more extensive repairs may require additional steps or professional assistance.
Photo Gallery




